what do i need to fill a bearing buddy

Download Commodity

Download Article

Bearing Buddy is a system of trailer bearing protectors designed to supercede your standard bearing grit caps and keep wet and dirt out of your bearings. They are especially useful for boat trailers or whatsoever other type of trailer that is prone to accumulating h2o in the bearings, which can corrode and harm them over fourth dimension. Like other types of bearing grit caps, all you accept to do to install your new Bearing Buddy protectors is hammer them into identify over the bearings.

1. 1

   Buy the correct size of Bearing Buddy caps before yous remove the dust caps. Add a decimal after the outset digit of the Bearing Buddy model number to know what the bore is in inches. Purchase the model number that corresponds to the bore of your wheel bearings.^[1]

   • For instance, Begetting Buddy model number 1938 is designed for utilise with begetting hubs that have a diameter of 1.928 in (4.90 cm).
   • You lot can choose betwixt chrome and stainless steel Bearing Buddy protectors. Notation that stainless steel is recommended for wheels that volition take contact with salt water.

2. two

   Tap a flat-head screwdriver nether the lip of the bearing caps using a hammer. The bearings and caps are in the exact middle of your wheels. Identify the edge of the screwdriver's flat head against the fissure where the bearing'south grit cap meets the bearing itself. Hitting the dorsum of the screwdriver with a hammer until information technology wedges between the begetting cap and the bearing.^[2]

   • Y'all don't have to jack upwardly the wheel or take the wheel off to install a Bearing Buddy protector because all you lot are doing is replacing the bearing dust cap, which can exist removed with the bicycle resting on the basis.
   • Note that y'all must repeat this procedure for each wheel that yous want to install a Bearing Buddy on.

   Tip: If you're regreasing your trailer wheel bearings, information technology could be a good time to install new Bearing Buddy protectors every bit well. Begetting Buddy caps will keep all the new grease make clean and within the bearings.

   Advert

3. iii

   Pry off the grit caps past using the screwdriver similar a lever. Work the screwdriver around the grit cap, pushing and pulling it similar a lever as you go. Go on prying away at the cap until it loosens all the way and pops off. Keep the grit caps you remove if you think you might demand them in the future or recycle them.^[iii]

   • All standard bearing caps just pop on and off, and so you don't need any special tools to remove them. Yet, there are special pliers called grit cap pliers that you could use if yous have them bachelor.

4. 4

   Wipe downwards the bearing hubs with a rag to make clean off whatsoever clay. Rub whatsoever muddy grease and other crud off the exposed surfaces of the begetting hub. This will clean it up and permit you examine information technology to brand certain it'southward in expert shape before you lot install a Begetting Buddy protector.^[4]

5. 5

   Inspect your bearings and replace them if they are rusty, damaged, or pitted. Proceed to install your new Begetting Buddy caps if the bearings look like smooth, undamaged metal. Stop and supervene upon the bearings before you get any further if you meet whatever rust or corroded pits in the metallic.^[5]

   • Bearing Buddy protectors are designed to proceed out moisture and clay that tin can corrode and damage your bearings. If you do end upwards replacing your bearings before you install the new caps, the Begetting Buddy caps should forestall the need to do so any time again in the about future.

   Advertizing

1. 1

   Hold a Begetting Buddy over a wheel'due south bearing. Orient the Begetting Buddy protector so that the more hollow side faces the begetting and the side with the nozzle in the eye faces outwards. Line the Bearing Buddy up with the wheel bearing and hold it in identify against the begetting.^[six]

   • Annotation that this process must exist done once for each bicycle bearing that you lot want to attach a Begetting Buddy to.

2. 2

   Hammer the Begetting Buddy into place with a rubber mallet. Whack the Bearing Buddy around all sides until it sits flush over the bearing. A rubber mallet volition prevent whatever damage to the Bearing Buddy.^[7]

   • If you don't have a safety mallet, you can place a apartment slice of scrap wood affluent confronting the Bearing Buddy and hit the surface of the wood with a normal hammer to push the Bearing Buddy into place.

   Warning: If yous can't hammer a Bearing Buddy securely into identify or information technology fits as well loosely, don't try to force information technology. You could end upwardly damaging the bearing. Double-check the diameter of your wheel bearings with a tape measure and brand sure you have the right size of Begetting Buddy caps.

3. three

   Fill the Bearing Buddy with begetting grease using a grease gun. Push the nozzle of the grease gun securely over the nozzle in the middle of the Begetting Buddy. Squeeze the grease gun'due south handle to shoot grease into the bearing until y'all see the lubricant oozing out around the nozzle of the Bearing Buddy.^[8]

   • Bearing Buddy caps have something called a weep pigsty, which prevents you from overfilling them with grease by letting it ooze out.

4. 4

   Place the rubber Begetting Buddy cover over the metallic cap. Push the blackness rubber sealing cover all the mode onto the metal Bearing Buddy cap. Press down firmly in the eye of the condom cover to strength out any air bubbles.^[9]

   • The rubber cap volition seal the Bearing Buddy to block out dirt and water, as well as keep all the grease safely packed inside.

5. five

   Repeat the entire process for each wheel. Remove the existing dust caps from each cycle on your trailer, wipe the bearings clean, and inspect them for rust and impairment. Hammer the Bearing Buddy protectors into place over the bearings, fill them with grease, and embrace them with the protective safe caps.^[10]

   • Notation that fifty-fifty if you only have 1 corroded or damaged bearing, you should e'er supervene upon all of them so that they are in equal condition.

   Advertising

Ask a Question

200 characters left

Include your email address to go a bulletin when this question is answered.

Submit

Advert

Things You'll Need

• Begetting Buddy
• Hammer
• Flat-caput screwdriver
• Rag
• Condom mallet
• Grease gun
• Bearing grease

About This Article

Thanks to all authors for creating a page that has been read 11,001 times.

Did this commodity help you?

sissonthadespecte.blogspot.com

Source: https://www.wikihow.com/Install-Bearing-Buddies

Share this post